Research/Method

RC (reverse circulation) drilling in mineral exploration

How RC drilling returns chips up dual-wall rods, its cost per metre against core and aircore, QA/QC and twin holes, and how to read RC results.

Updated November 20269 min read

RC (reverse circulation) drilling breaks the rock with a pneumatic hammer and a tungsten-steel bit, and compressed air goes down between the outer and inner tubes of dual-wall rods and blows the chips back up the inner tube to a cyclone at surface (Geological Survey of Western Australia, GSWA). Companies drill RC for exploration and resource holes and for grade control in open pits (Ramelius, May 2024, Sandvik). It costs less per metre than core drilling (Novo Resources), and geologists switch to core for intact rock and oriented structural measurements (Imdex). In a release, you read RC results as downhole intervals and grades, and you check the true width, the higher-grade intervals inside each interval, wet samples and composites.

Dual-wall rods and hammer

The air goes down the annulus (the gap between the outer and inner tubes) and comes back up inside the inner tube with the cuttings (GSWA). That's the reverse of the air path in open-hole drilling such as rotary air blast (RAB), where the air blows the cuttings up outside the rods. With a face-sampling hammer, the cuttings enter the sample stream at the bit face, and Sandvik describes an isolated sample route from the bit face to the cone splitter on its RC rig (Sandvik). JORC Table 1 asks whether the company used a face-sampling bit (JORC Code), and Ramelius Resources drills its RC holes with 5¾-inch face-sampling hammers (Ramelius, May 2024).

At surface, a cyclone collects the cuttings for sampling (GSWA). Ramelius collects its RC samples at 1 m intervals in a cyclone beside the rig, splits off 2 to 3 kg with a riffle or cone splitter into numbered bags, and lays the rest on the ground for logging (Ramelius, May 2024). The exploration guidelines from CIM (the Canadian Institute of Mining, Metallurgy and Petroleum) say RC sample intervals are typically a constant length (CIM), and JORC's example of an industry-standard description is RC drilling for 1 m samples, with 3 kg pulverized to a 30 g charge for fire assay (JORC Code).

Drillers routinely drill RC holes to 500 m with larger rigs and higher air pressure than open-hole drilling (GSWA), and Boart Longyear lists RC rigs with depth capacities up to 1,219 m (4,000 feet) (Boart Longyear). A company can drill an RC precollar through the upper part of a hole and finish it with a diamond tail (GSWA).

RC, core, aircore and RAB

Method Sample Sample return Ground Base rate
Diamond core Solid core, 36.4 mm (BQ) to 85.0 mm (PQ) Inner tube winched up on a wireline Rock, to a kilometre or more Highest
RC Chips, usually 1 m samples Air down the annulus, chips up the inner tube Hard rock, routinely to 500 m About a quarter of diamond
Aircore Chips, occasionally small pieces of core Air down the annulus, chips up the inner tube Unconsolidated and weathered ground About an eighth of diamond
RAB Chips Air blows chips up outside the rods Rock or sediment, with a blade bit, or a hammer for thin hard layers About a tenth of diamond

Core sizes come from Boart Longyear's catalogue, core depth from Natural Resources Canada, the relative base rates and RAB bit notes from Novo Resources, and the rest from GSWA. Novo says consumables, slow penetration, standby, mobilization and water cartage often double the base rate, and RC and diamond rates rise with depth. The drill types table adds rotary hammer, vacuum, auger and sonic drilling.

Aircore uses the same dual-tube air return as RC, but its three-blade steel or tungsten bit cuts unconsolidated ground, and the driller often switches to a hammer at the base of the hole in saprock (partly weathered bedrock) (GSWA). Novo Resources says RAB's sample quality is generally poorer than the other methods' because of downhole contamination (Novo Resources). Ramelius composites its aircore samples to 4 m and doesn't use its aircore results in resource estimates (Ramelius, May 2024).

Novo lists aircore and RAB for first-pass and early-stage work and RC and diamond drilling for advanced stages of mineral exploration.

So drill RC to test grade in fresh rock at the lower cost per metre, and switch to core for oriented structural measurements (Imdex), material for geotechnical tests (CIM) or holes deeper than RC's routine 500 m (GSWA). Many programs combine them, and Hot Chili drilled most of its Cortadera diamond holes in Chile from RC precollars averaging 200 m, then HQ core to about 520 m and NQ2 core below that, to a maximum of 1,473.5 m (Hot Chili, February 2024).

Sample quality

RC returns the chips inside the rods, so the hole wall above the sampling depth can't contaminate the sample (GSWA), and Novo Resources says RC generally gives more reliably uncontaminated samples than RAB or aircore (Novo Resources).

JORC asks how the company recorded and assessed chip recoveries, and whether a relationship between recovery and grade, or a preferential loss or gain of fine or coarse material, biased the samples (JORC Code). Ramelius's supervising geologist inspects each bulk RC sample for a clean recovery, and the company flags wet, contaminated or poor returns in its database and checks those zones against the assays (Ramelius, May 2024).

For chips, JORC asks whether the company riffle split, tube sampled or rotary split them, and whether it sampled them wet or dry (JORC Code). Ramelius records wet samples in its database, and at Eridanus it spear samples the occasional wet sample from a plastic bag instead of splitting it (Ramelius, May 2024). It also collects a field duplicate from every 20th RC sample.

JORC asks whether the company composited samples (JORC Code), and some of Ramelius's historic RC samples are 2 m or 4 m composites (Ramelius, May 2024). A composite gives one assay for the whole length, so a 4 m composite can average a 1 m high-grade sample with three low-grade metres.

QA/QC

Ramelius inserts a high- or low-grade standard or a blank every 20th sample alongside its field duplicates, and it checks each standard and blank against its tolerance and the field duplicates for gold bias (Ramelius, May 2024). Hot Chili cone splits its RC chips on 2 m intervals into two nominal 12.5% splits, sends one to the lab and keeps the other, and it submits a field duplicate for 1 in 25 samples (Hot Chili, February 2024).

JORC Table 1 asks whether the company drilled twinned holes (JORC Code), and a twin drilled beside an earlier hole tests whether one sampling method biases the grade. Hot Chili drilled five sets of twin holes at Cortadera to compare its RC samples with historical HQ diamond and RC holes, and saw a slight negative bias in the RC samples in select intervals but no material variance overall (Hot Chili, February 2024).

Grade control

Open-pit operators drill RC for grade control, which is close-spaced drilling to separate ore from waste before mining (Sandvik, September 2021).

Ramelius drills grade control at its Eridanus pit at Mt Magnet, Western Australia, on a nominal 7.5 m by 7.5 m RC collar spacing from 20 m benches, with holes at an average -60° dip to 54 m (Ramelius, May 2024). Ramelius used the grade control drilling to classify the Measured part of its May 2024 Eridanus resource (21 Mt at 1.7 g/t gold for 1.2 million ounces in all categories).

Ramelius plans its RC infill holes (between existing holes) and step-out holes (extending a zone) on nominal 20 to 40 m centres, depending on the prospect's stage (Ramelius, May 2024), and hole spacing explains how spacing sets the resource category.

Drill results

In its May 2024 release, Ramelius lists each Eridanus RC hole with its collar (easting, northing and RL, the collar elevation) and intercepts (Ramelius, May 2024).

Hole Easting Northing RL Azimuth/dip End of hole From To Interval Gold
ERI_245_0157 576710 6894256 245 256°/-75° 186 m 178 m 186 m 8 m 4.30 g/t
Including 178 m 179 m 1 m 30.5 g/t

The interval is 34.4 gram-metres (8 m × 4.30 g/t), and the 1 m sample accounts for 30.5 of them, so the other 7 m average about 0.56 g/t. The interval ends at the 186 m end-of-hole depth, so Ramelius stopped drilling in mineralization.

Ramelius calculates its intervals from 1 m RC samples, reports intervals of 2 m or more above 1 g/t gold with up to 2 m of internal dilution (lower-grade samples inside the interval) on a 0.50 g/t lower cut, and applies no top cut (cap on high assays). It measures intersection lengths along the hole and says they're usually not the true width.

For an RC release, also check whether the intervals come from 1 m samples or composites, whether any samples were wet, and the depth of any diamond tail, because JORC Table 1 asks for all three (JORC Code). In Canada, NI 43-101 requires every written disclosure of RC or core results on a material property to include the location, azimuth and dip of each hole, the depth of the sample intervals, the true widths where known and any significantly higher-grade intervals within a lower-grade intersection (NI 43-101, section 3.3).

Permits and cost

On BLM land, casual use excludes truck-mounted drilling, so an RC program needs at least a notice (43 CFR 3809.5, permits by jurisdiction).

Western Australia's co-funded drilling guidelines count the metre rate, minimum shift rate, mobilization, water cartage, downhole surveys and active standby as direct costs for percussion chips and core alike (WA Government), so compare RC quotes on the all-in cost per metre.

GeoTheories for prior drilling

Each GeoTheories project page shows the historic RC and core holes, intercepts and end-of-hole depths for any property from assessment reports and government drill hole databases (historic drill holes and assessment reports), so you see where earlier operators drilled and how deep before you plan holes. In GeoTheories, you check a company's new RC results against the earlier holes on the same ground before you buy shares.

Agents build out your thesis from the deposit model and then walk it through the geology, geophysics, geochem, satellite alteration, mine records, drill holes, filings and claims on that ground, in any country or mining district, including Yukon, the Athabasca Basin, Greenland, Argentina, Sweden and South Australia. Solo is $299 a month or $2,499 a year, and Team is $699 a month or $5,849 a year for up to 5 people, through self-serve checkout.

FAQ

What is RC drilling?

RC (reverse circulation) drilling breaks the rock with a hammer, and compressed air returns the chips up the inner tube of dual-wall rods to a cyclone at surface (GSWA).

Why is it called reverse circulation?

It's called reverse circulation because the air goes down between the outer and inner tubes and back up inside the inner tube with the cuttings, which is the reverse of open-hole drilling such as RAB, where the cuttings come up outside the rods (GSWA).

What's the difference between RC and diamond drilling?

RC returns broken rock chips and diamond drilling returns solid core (GSWA). RC costs less per metre, core gives the most representative sample (Novo Resources), and oriented core gives the structural measurements for the geological model (Imdex).

How deep can RC drilling go?

Drillers routinely drill RC holes to 500 m (GSWA), and Boart Longyear lists RC rigs with depth capacities up to 1,219 m (4,000 feet) (Boart Longyear).

Do companies use RC drilling in resource estimates?

Yes, Ramelius estimated its Eridanus resource from RC and diamond holes and classified the Measured category from its RC grade control drilling (Ramelius, May 2024).

How much does RC drilling cost per metre?

Novo Resources' drilling glossary puts RC's base rate at about a quarter of diamond drilling's, and says consumables, slow penetration, standby, mobilization and water cartage often bring the all-in cost to double the base rate (Novo Resources). The rate commonly rises with depth.

What are the disadvantages of RC drilling?

RC returns chips, so geologists can't orient structures in them (Imdex), and wet samples need extra handling (Ramelius dries or spear samples them and flags them in its database) (Ramelius, May 2024). Routine RC holes are up to 500 m deep, against a kilometre or more for core (GSWA, NRCan), and Hot Chili's twin holes at Cortadera showed a slight negative bias in RC samples in select intervals (Hot Chili, February 2024).